Altigen MAXCS 7.0 Update 1 MultiVOIP Configuration Manual do Utilizador Página 1

MAXCS Release 7.0 Update 1 MultiVoIP Gateway Configuration Guide November 25, 2014 Intended audience: AltiGen Authorized Partners

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 10 of 27 Follow these steps to configure the SIP extensions: 1. In MaxCS Administrator, sel

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 11 of 27 6. Select Configuration > Interface and configure these parameters: • Set Sel

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 12 of 27 7. Select Phone Book > Outbound Phone Book and create an entry with the followi

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 13 of 27 9. Repeat the same process for extension 252 by adding a new entry where Remove Pr

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 14 of 27 To configure SIP-Tie Trunks, follow these steps: 1. Open the MultiVoIP configurati

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 15 of 27 • Set Caller ID Type to BellCore • Check the Caller ID Enable check box 4. Sele

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 16 of 27 Analog extensions behind the MVP gateway are optional. If the analog extensions are

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 17 of 27 5. Log into the MultiVoIP tool. 6. Select Phone Book > Inbound Phone Book and

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 18 of 27 Outgoing Calls to PSTN Using Out Call Routing (Optional) To make a call to the outs

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 19 of 27 To configure outgoing PSTN call via Out-call routing, follow these steps: 1. Log i

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 2 of 27 Contents Introduction ...

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 20 of 27 7. Select all the analog trunks (in this example, from “02:000” to “02:011”) as Me

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 21 of 27 Verification At this point, you should be able pick up extension 104 and make an ou

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 22 of 27 5. Select PBX > Out Call Routing Configuration > Dialing Pattern and add a

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 23 of 27 Verification 1. Follow Figure 3. Use extension 104 to dial 15102520004. The call s

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 24 of 27 3. Move extensions 210, 251 and 252 to the Members list. (Extensions 251 and 252 a

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 25 of 27 Under Dialed Digit Translator: 1. Log into MaxCS Administrator and select System &

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 26 of 27 To configure emergency gateway dialing, follow these steps: 1. Log into the MultiV

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 27 of 27 AltiGen Technical Support AltiGen does not provide general configuration support fo

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 3 of 27 Introduction This document provides guidelines for setting up a MultiTech gateway a

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 4 of 27 2. Select Configuration > Call Signaling > SIP. Set Signaling Port to 5060.

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 5 of 27 6. Select Phone Book > Outbound Phone Book. 7. Either create a new entry or ed

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 6 of 27 Enterprise Manager Configuration 1. Open Enterprise Manager and log in. 2. Select

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 7 of 27 3. Add a new codec profile named MVP Gateway. Set the following parameters: • Set

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 8 of 27 The “Connect Voice Stream to Server” Option MaxCSIP Address10.10.0.237MVP 410AltiGen

MAXCS 7.0 Update 1MultiVoIP Configuration Guide Page 9 of 27 Under the following conditions, the system administrator will need to check the Conn